Email Alert  RSS
工艺探讨

高炉风口用铜基体防护涂层的制备、微结构和性能研究

展开
  • 武汉科技大学省部共建耐火材料与冶金国家重点实验室,湖北 武汉 430081
王周福(1965-),教授,博导,主要研究方向为防护涂层、超高温结构陶瓷、耐火材料与新型节能材料,电话:027-68862933,E-mail:whwangzf@126.com

收稿日期: 2022-09-15

  修回日期: 2022-10-15

  录用日期: 2022-11-07

  网络出版日期: 2023-08-04

基金资助

国家自然科学基金(U21A2057)(U20A20239);2021 年湖北省科技计划项目(2021BAD002)资助


Preparation,Microstructure and Properties of Copper Matrix Protective Coatings for Blast Furnace Tuyere

Expand
  • The State Key Laboratory of Refractories and Metallurgy,Wuhan University of Science and Technology,Wuhan 430081,China

Received date: 2022-09-15

  Revised date: 2022-10-15

  Accepted date: 2022-11-07

  Online published: 2023-08-04

摘要

为了延长高炉风口的有效服役寿命,以纯铜板为基材,NH4Cl 为催渗剂,以镍、铁、铝为共渗剂的主要成分,采用包埋共渗法在纯铜基体表面制备了防护涂层。研究了催渗剂含量、共渗剂配比、保温时间对防护涂层及涂层/基体界面结构的影响。利用XRD、SEM、EDS 对所制备的涂层物相组成与显微结构进行了表征,并评价了涂层的显微维氏硬度。结果表明:通过调节催渗剂NH4Cl 的含量和共渗剂Ni ∶Fe ∶Al 的比例,经热处理后可制备出与纯铜基体呈冶金结合的涂层。铝元素渗入到铜基体后,形成的渗层具有明显的渐变结构,使材料的显微维氏硬度明显提高。渗层中“高铝相”的存在阻碍了铜基体的位错运动,进一步提高了材料的显微硬度。

本文引用格式

乔恩涛, 王周福, 马妍, 刘浩, 王玺堂 . 高炉风口用铜基体防护涂层的制备、微结构和性能研究[J]. 材料保护, 2023 , 56(3) : 74 -80 . DOI: 10.16577/j.issn.1001-1560.2023.0062

Abstract

In order to prolong the effective service life of blast furnace tuyeres,a protective coating was prepared on the surface of pure copper substrate by embedding co-infiltration method using pure copper plate as base material,NH4 Cl as infiltration catalyst,and nickel,iron and aluminum as main components of co-infiltration agent.The effects of infiltration agent content,co-infiltration agent ratio and holding time on the protective coating and coating/substrate interface structure were studied.The phase composition and microstructure of the as-prepared coatings were characterized by XRD,SEM and EDS,and the micro-Vickers hardness of the coatings was evaluated.Results showed that by adjusting the content of NH4Cl catalyst and the ratio of Ni: Fe: Al in co-infiltration agent,a coating metallurgically bonded to the pure copper substrate could be prepared after heat treatment.After the aluminum element penetrated into the copper matrix,the formed infiltration layer had an obvious gradient structure,which significantly improved the micro-Vickers hardness of the material.The existence of “high aluminum phase”in the infiltration layer hindered the dislocation movement of the copper matrix and further improved the microhardness of the material.blast furnace tuyere;pure copper;embedded co-infiltration;coating;microhardness

参考文献

[1] ZHANG J,WANG R D,HU R,et al.Failure mode and mechanism of a blast furnace tuyere[J].Engineering Failure Analysis,2022,137:106 294.

[2] GORBATYUK S M,SAYFULLAEV S,KOBELEV O A,et al.Choice of thermal insulation for burnout protection of a blast furnace blast tuyere[J].Materials Today: Proceedings,2021,38(4):1 388-1 391.

[3] 章 超,吕金金,白 丹,等.高炉风口小套表面防护技术的研究进展[J].表面技术,2021,50(4):135-150.ZHANG C,LV J J,BAI D,et al.Research process of surface protection technology for tuyere small sleeve of blast furnace[J].Surface Technology,2021,50(4):135-150.

[4] 孙丽月.纯铜表面金属夹嵌陶瓷复合涂层技术研究[D].阜新:辽宁工程技术大学,2009.SUN L Y.Research on the properties of metal embedded ceramic composite coating in copper[D].Fuxin: Liaoning Technical University,2009.

[5] XIANG X,WANG X L,ZHANG G K,et al.Preparation technique and alloying effect of aluminide coatings as tritium permeation barriers: A review[J].International Journal of Hydrogen Energy,2015,40(9): 3 697-3 707,

[6] 胡 坚.高炉风口长寿化堆焊工艺及装置研究[D].武汉:华中科技大学,2015.HU J.Research on longevity arc deposition process and equipment of blast furnace tuyere[D].Wuhan:Huazhong University of Science & Technology,2015.

[7] 陆隆文,胡 坚,张海鸥,等.面向高炉风口小套长寿化的表面堆焊工艺[J].特种铸造及有色合金,2016,36(5):469-473.LU L W,HU J,ZHANG H O,et al.Surface overlaying welding for longe-service sleeve of blast furnace tuyere [J].Special Casting and Non-ferrous Alloy,2016,36(5):469-473.

[8] ZHANG C,WANG R D,ZHANG J,et al.Investigation on high-temperature stability of Ni60A alloy coating on copper substrate fabricated by plasma cladding[J].Materials Chemistry and Physics,2022,287:126 378.

[9] 张冀翔,徐修炎,宋健斐,等.粉末包埋渗铝研究进展[J].热加工工艺,2018,47(4):22-25.ZHANG J X,XU X Y,SONG J F,et al.Resrarch progess of pack cementation aluminizing[J].Hot Working Technology,2018,47(4):22-25.

[10] 李广忠,王 昊,金 辉,等.渗铝G115 钢的制备及其在模拟煤炭超临界水气化中的腐蚀行为[J].材料保护,2021,54(12):30-35.LI G Z,WANG H,JIN H,et al.Preparation of aluminizing G115 steel and its corrosion behavior in simulation supercritical water gasification of coal[J].Materials Protection,2021,54(12):30-35.

[11] WANG Y,LIU D W,FENG S J,et al.Preparation of tritium permeation barrier consisting of titanium by the pack cementation method[J].Surface and Coatings Technology,2016,307: 271-277.

[12] 秦泽华,杨 阳,黄祖江,等.铌基合金表面Al-B 包埋共渗层的组织及抗氧化性能[J].材料保护,2015,48(7):15-19.QIN Z H,YANG Y,HUANG Z J,et al.Microstructure and oxidation resistance of Al-B embedded co-infiltrating Layer on Niobium-Based Alloys [J].Materials Protection,2015,48(7):15-19.

[13] CHEN X H,ZHANG P Z,WEI D B,et al.Preparation and characterization of Cr/CrC multilayer on γ-TiAl alloy by the double glow plasma surface alloying technology[J].Materials Letters,2018,215: 292-295.

[14] 张金龙,乔 杰,王晓霞.高炉风口Al-Fe 共渗表面强化研究[J].内蒙古科技大学学报,2015,34(2):118-121.ZHANG J L,QIAO J,WANG X X.Study on surface of blast furnace tuyere by Al -Fe penetration[J].Inner Mongolia University of Science and Technology,2015,34 (2):118-121.

[15] 刘建局.纯铜铝铁共渗的实验研究[D].上海:上海交通大学,2008.LIU J J.Experimental study on the copper Fe-aluminizing[D].Shanghai:Shanghai Jiao Tong University,2008.

[16] 袁庆龙,苏永安.纯铜表面Al-Ni 基自熔合金粉末共渗研究[J].太原理工大学学报,2002,33(3):320-323.YUAN Q L,SU Y A.Multielement penetration of Al and Nibased self-fusion alloy powder on the surfance of pure copper[J].Journal of Taiyuan University of Technology,2002,33(3):320-323.

[17] 李涌泉.TiAl 合金表面Si-Al-Y 共渗层的组织与性能研究[D].西安:西北工业大学,2014.LI Y Q.Microstructure and performance of Si-Al-Y co-deposition coating on the surfance of TiAl alloy[D].Xi’an:Northwestern Polytechnical University,2014.

[18] LI Y Q,XIE F Q,WU X Q.Microstructure and high temperature oxidation resistance of Si-Y co-deposition coatings prepared on TiAl alloy by pack cementation process[J].Transactions of Nonferrous Metals Society of China,2015,25(3):803-810.

文章导航

/