Effect of Nano-BN Particles on Microstructure and Wear Resistance of Micro-Arc Oxidation Coating on 7075 Aluminum Alloy

YANG Fan, QI Yuming, FU Wenkai, HUANG Xin, CUI Xuejun

doi:10.16577/j.issn.1001-1560.2023.0156

Materials Protection >

2023 , Vol. 56 >Issue 7: 17 - 24

DOI: https://doi.org/10.16577/j.issn.1001-1560.2023.0156

Effect of Nano-BN Particles on Microstructure and Wear Resistance of Micro-Arc Oxidation Coating on 7075 Aluminum Alloy

Expand

Material Corrosion and Protection Key Laboratory of Sichuan Province，School of Materials Science and Engineering，Sichuan University Science and Engineering，Zigong 643000，China

Received date: 2023-03-06

Revised date: 2023-04-11

Accepted date: 2023-05-15

Online published: 2023-08-18

Fold

Abstract

In order to improve the wear resistance of 7075 aluminum alloy surface，the hard ceramic coating on the aluminum alloy surface was constructed by micro-arc oxidation technology in the electrolyte solution doped with nano-BN particles.The effects of the addition of nano-BN particles on the arc initiation voltage of the micro-arc oxidation process，surface morphology，porosity，phase composition，thickness，roughness，microhardness and friction and wear properties of coating were investigated by means of scanning electron microscopy (SEM)，energy dispersive spectrometer (EDS)，X-ray diffractometer (XRD)，photoelectron spectrometer (XPS)，roughness tester，microhardness tester，friction and wear testing machine.Results showed that the coatings were mainly composed of α-Al2O3 and γ-Al2O3 phase.Nano-BN particles increased the arc initiation voltage，and increased the thickness，roughness and hardness of coating.When the concentration of nano-BN particles was 0.3 g/L，the overall performance of the as-obtained micro-arc oxidation coating was the best.At this time，the number of micropores in the coating was small，the pore size was small，and the surface density was high.Compared with the coating prepared in the basic electrolyte，the coating’s surface porosity decreased from 6.617%to 3.518%.Meanwhile，the hardness reached the highest value 916.7 HV10 N，the thickness was 20 μm，and the roughness was 2.38 μm.The friction coefficient was reduced to 0.7，and the wear rate decreased to 7.84×10-5 mm3/(N·m).

Key words： micro-arc oxidation; 7075 aluminum alloy; nano-BN particles; structure; wear resistance

Cite this article

YANG Fan, QI Yuming, FU Wenkai, HUANG Xin, CUI Xuejun . Effect of Nano-BN Particles on Microstructure and Wear Resistance of Micro-Arc Oxidation Coating on 7075 Aluminum Alloy[J]. Materials Protection, 2023 , 56(7) : 17 -24 . DOI: 10.16577/j.issn.1001-1560.2023.0156

References

[1] 李昊宸，王赫男，马雪菲.铝合金微弧氧化工艺研究现状[J].热加工工艺，2021，50(22): 1-5.LI H C，WANG H N，MA X F.Research status on microarc oxidation of aluminum alloy[J].Hot Working Technology，2021，50(22): 1-5.

[2] 苗景国.超硬铝合金7075 微弧氧化陶瓷层的微结构及性能研究[D].武汉: 武汉科技大学，2013.MIAO J G.Study of the microstructure and properties of ceramic coatings prepared by micro-arc oxidation on surface of 7075 super-hard aluminum alloy[D].Wuhan: Wuhan University of Science and Technology，2013.

[3] 齐玉明，彭振军，刘百幸，等.钛合金表面高硬度微弧氧化膜的制备和耐磨性研究[J].表面技术，2019，48(7):81-88.QI Y M，PENG Z J，LIU B X，et al.Fabrication and wear resistance of hard micro arc oxidation coatings on Ti alloys[J].Surface Technology，2019，48(7): 81-88.

[4] 雷欣，林乃明，邹娇娟，等.铝合金微弧氧化的研究进展[J].表面技术，2019，48(12): 10-22.LEI X，LIN N M，ZOU J J，et al.Research progress of micro-arc oxidation on aluminum alloys [J].Surface Technology，2019，48(12): 10-22.

[5] 薛文斌，邓志威，陈如意，等.铝合金微弧氧化膜与基体界面区的硬度和弹性模量分布[J].金属学报，1999，35(6): 638-642.XUE W B，DENG Z W，CHEN R Y，et al.Distributions of hardness and elastic modulus near the interface between aluminum alloy substrate and microarc oxidation coating[J].Acta Metallrugica Sinica，1999，35(6): 638-642.

[6] 陈彬.微弧氧化工艺参数对膜质量及性能的影响[D].长春: 长春工业大学，2013.CHEN B.Effects of process parameters on the quality and properties of aluminum alloy micro - arc oxdation [D].Changchun: Changchun University of Technology，2013.

[7] 贺子凯，唐培松.电流密度对微弧氧化膜层厚度和硬度的影响[J].表面技术，2003，32(3): 21-24.HE Z K，TANG P S.Effects of current density on thickness and hardness of microarc oxide film[J].Surface Technology，2003，32(3): 21-24.

[8] 赵晖，朱其柱，金光，等.电流密度对纯铝微弧氧化膜结构及硬度的影响[J].深圳大学学报: 理工版，2014，31 (1): 83-87.ZHAO H，ZHU Q Z，JIN G，et al.Effect of current density on micro-structure and micro-hardness of micro- arc oxidation coatings on aluminum[J].Journal of Shenzhen University: Science and Engineering，2014，31 (1): 83-87.

[9] 贾秋荣，崔红卫，张甜甜，等.镁合金微弧氧化技术的研究概况[J].材料保护，2018，51(8): 108-113.JIA Q R，CUI H W，ZHANG T T，et al.Genreal situation on research of micro-arc oxidation technology of magnesium alloys[J].Materials Protection，2018，51(8): 108-113.

[10] 齐玉明，刘思勤，罗兰，等.镁合金表面PEF 膜与PEO 膜腐蚀防护行为的对比研究[J].表面技术，2021，50(6): 41-54.QI Y M，LIU S Q，LUO L，et al.Comparison in corrosion behaviour of PEF and PEO coatings on Mg alloy[J].Surface Technology，2021，50(6): 41-54.

[11] 刘百幸，彭振军，梁军.TC4 合金微弧氧化膜的摩擦磨损性能及其失效机理研究[J].摩擦学学报，2019，39(1): 50-56.LIU B X，PENG Z J，LIANG J.Investigation of friction and wear performance and failure mechanism of PEO coating on TC4 alloy[J].Tribology，2019，39(1): 50-56.

[12] 李鑫，张晟豪，王子恒，等.稀土氧化钇对AZ31B 镁合金微弧氧化膜层微观组织和性能的影响[J].材料保护，2022，55(10): 37-42.LI X，ZHANG S H，WANG Z H，et al.Effect of rare earth Y2O3 on the microstructure and properties of AZ31B magnesium alloy coatings prepared by micro -arc oxidation[J].Materials Protection，2022，55(10): 37-42.

[13] 于娟，汪杰，贺崇，等.TiO2纳米粒子对铝锂合金微弧氧化膜结构及性能的影响[J].中国表面工程，2019，32(4): 36-44.YU J，WANG J，HE C，et al.Effects of nano-TiO2 particles on structure and properties of micro-arc oxidation film on Al-Li alloy[J].China Surface Engineering，2019，32(4):36-44.

[14] 常海，郭雪刚，文磊，等.SiC 纳米颗粒对TC4 钛合金微弧氧化涂层组织结构及耐蚀性能的影响[J].材料工程，2019，47(3): 109-115.CHANG H，GUO X G，WEN L，et al.Influence of SiC nanoparticles on microstructure and corrosion behavior of microarc oxidation coatings formed on TC4 alloy[J].Journal of Materials Engineering，2019，47(3): 109-115.

[15] SAVONOV G，CAMARINHA M，ROCHA L O，et al.Study of the influence of the RRA thermal treatment and plasma nitriding on corrosion behavior of 7075-T6 aluminum alloy[J].Surface and Coatings Technology，2019，734:736-744.

[16] YANG Z，WANG R Q，LIU C，et al.The electrochemical corrosion behavior of plasma electrolytic oxidation coatings fabricated on aluminum in silicate electrolyte[J].Journal of Materials Engineering and Performance，2019，28(2/3):3 652-3 660.

[17] KONG D，LIU H，WANG J.Effects of micro arc oxidation on fatigue limits and fracture morphologies of 7475 high strength aluminum alloy[J].Journal of Alloys and Compounds，2015，650: 393-398.

[18] 张宇，赵燕伟，宋仁国.纳米TiO2添加剂对ZL101A 铝合金微弧氧化陶瓷涂层性能的影响[J].热加工工艺，2017，46(18): 153-156.ZHANG Y，ZHAO Y W，SONG R G.Effects of nano-TiO2 additive on properties of MAO ceramic coatings on ZL101A Al alloy[J].Hot Working Technology，2017，46(18):153-156.

[19] 吴德凤，雷源源，张晓燕，等.纳米SiO2添加剂对铸造铝铜合金微弧氧化陶瓷层耐磨性的影响[J].表面技术，2013，42(5): 42-44.WU D F，LEI Y Y，ZHANG X Y，et al.Effect of nano-SiO2 additive on the microstructure and wear resistance of micro-arc oxidation ceramic coating on casting aluminum alloy[J].Surface Technology，2013，42(5): 42-44.

[20] 黄丹，张晓燕，吴德凤，等.纳米α-Al2O3添加剂对铝合金微弧氧化膜层性能的影响[J].表面技术，2014，43(4): 43-47.HUANG D，ZHANG X Y，WU D F，et al.Effects of nano α-Al2O3 additive on the performance of micro-arc oxidation coating formed on aluminum alloy[J].Surface Technology，2014，43(4): 43-47.

[21] 周立涛，刘伟.Al2O3、六方BN 纳米润滑油的摩擦学性能试验研究[J].润滑与密封，2007(2): 159-161.ZHOU L T，LIU W.Research on the friction behavior of lubricant Oil contained Al2O3 and six squares BN Nano meter grain[J].Lubrication Engineering，2007(2): 159-161.

[22] 魏国栋，曹晓明，马瑞娜，等.纳米BN 对1060 铝微孤氧化膜层性能的影响[J].表面技术，2017，46(5):7.WEI G D，CAO X M，MA R N，et al.Effect of Nano BN Additive on Performance of Micro-arc Oxide Film Formed on 1060 Aluminum[J].Surface Technology，2017，46(5):7.

Options

Outlines

模态框（Modal）标题

Abstract

Cite this article

References