The thickness and density of the zirconia ceramic layer formed on the surface of the zirconium alloy cladding are the main factors affecting its wear resistance. In this paper, the variation of thickness and density of zirconia ceramic layer with time during thermal oxidation of three different composition zirconium alloys, Zr-Sn, Zr-Nb, and Zr-Sn-Nb, in typical high temperature air at 560 ℃ and 600 ℃ was studied. The maximum thickness of the dense zirconia ceramic layer that could be formed by thermal oxidation of zirconium alloy cladding with different compositions in air during the experimental characterization time was explored. Results showed that the maximum thickness growth rate of zirconia ceramic layer in Zr-Nb zirconium alloy cladding at typical temperatures during the test period was the largest, that of Zr-Sn-Nb zirconium alloy cladding took second place, and that of Zr-Sn zirconium alloy cladding was the smallest. The thickness growth rate of zirconia ceramic layer in zirconium alloy cladding with the same composition at 600 ℃ was about twice that of 560 ℃. When the thicknesses of zirconia ceramic layer of Zr-Sn and Zr-Sn-Nb zirconium alloy cladding were 4~5 μm and 9~10 μm at 600 ℃, respectively, the obvious crack were observed, while the zirconia ceramic layer thickness of Zr-Nb zirconium alloy cladding reached 12 μm at 600 ℃, the density of this ceramic layer was good, and no obvious cracks were observed.
SUN Guo-cheng
,
ZHANG Guo-liang
,
CHEN Liu-tao
,
CHEN Xiao-yang
. Preliminary Study of Characteristics of Thermal Oxidation Film of Zirconium Alloy Cladding in Typical High Temperature Air[J]. Materials Protection, 2023
, 56(6)
: 190
-193
.
DOI: 10.16577/j.issn.1001-1560.2023.0152
[1] 林庆选,栾丽敏,程世福,等. R60705锆合金的表面氧化改性[J]. 金属热处理,2013,38(1):104-107.
LIN Q X, LUAN L M, CHENG S F, et al. Surface oxidation modification of R60705 zirconium alloy[J]. Metal Heat Treatment, 2013, 38 (1): 104-107.
[2] LUO Y, YANG T, RAO X, et al. Thermal oxidation of Zr-2.5Nb alloy and its biotribological properties[J]. International Journal of Advanced Manufacturing Technology, 2018,96: 1 539-1 543.
[3] ZAGORKA K, RUZICA M, DAFINKA S. Air-thermal oxidation of zirconium[J]. Journal of Engineering & Processing Management, 2017, 9(1): 81-85.
[4] 杨 婷. Zr-2.5Nb合金的热氧化工艺及生物相容性研究[D]. 徐州:中国矿业大学,2017.
YANG T. Thermal oxidation process and biocompatibility of Zr-2.5Nb alloy[D]. Xuzhou: China University of Mining and Technology, 2017.
[5] 周邦新,李 强,黄 强,等. 水化学对锆合金耐腐蚀性能影响的研究[J]. 核动力工程,2000,21(5):439-447.
ZHOU B X, LI Q, HUANG Q, et al. Study of the influence of water chemistry on corrosion resistance of zirconium alloy[J]. Nuclear Power Engineering, 2000, 21(5): 439-447.
[6] COX B. Some thought on the mechanisms of in-reactor corrosion of zirconium alloys[J]. Journal of Nuclear Materials, 2005,336:331-368.
[7] 杨忠波,赵文金. 锆合金耐腐蚀性能及氧化特性概述[J]. 材料导报,2010,24(9):120-125.
YANG Z B, ZHAO W J. Overview of corrosion resistance and oxidation characteristics of zirconium alloys[J]. Materials Reports, 2010, 24(9): 120-125.
[8] ZHOU B X, YAO M Y, LI Z K. Optimization of N18 Zirconium Alloy for Fuel Cladding of Water Reactors[J].Journal of Materials Science & Technology, 2012, 28(7):606-613.
[9] JORDAN L, PATRICK M, JOHN-PAUL S, et al. Oxidation behavior of Zirconium, Zircaloy-3, Zircaloy-4, Zr-1Nb and Zr-2.5Nb in air and oxygen[J]. Nuclear Materials and Energy, 2019,20: 1-9.
[10] ARTHERM, AYLIN Y, MARCELO J, et al. Zirconium alloys for supercritical water reactor applications: Challenges and possibilities[J]. Journal of Nuclear Materials, 2007,371: 61-75.